High Risk Courses

HIGH RISK (Not Funded)

  • Course Code and Name:
    TLILIC0005- Licence to operate a boom-type elevating work platform (boom length 11 metres or more)

    This unit specifies the outcomes required to operate a boom-type elevating work platform (boom length 11 metres or more) for licensing purposes, and involves the operation of a telescoping device, hinged device, or articulated device or any combination of these used to support a platform on which personnel, equipment and materials may be elevated to perform work. The 11 metre boom length shall be taken to mean the greater of the following:

    (a) The vertical distance from the floor of the platform to the surface supporting the elevating work platform with the platform at its maximum height; or

    (b) The nominal reach, measured horizontally from the centre point of rotation to the outer edge of the platform in its most extended position.

    Pre-Requisites:
    Nil.

  • Course Code and Name:
    CPCCLDG3001A Licence to perform dogging

    This unit specifies the outcomes required to perform slinging techniques, including the selection and inspection of lifting gear and/or the directing of the crane operator in the movement of the load when the load is out of view of the crane / operator for licensing purposes.

    Pre-Requisites:
    Not applicable to this course.

  • Course Code and Name:
    TLILIC2001 – Licence to operate a forklift truck

    This unit specifies the skills and knowledge required to operate a forklift truck safely.
    Forklift truck means a powered industrial truck equipped with lifting media made up of a mast and an elevating load carriage to which is attached a pair of fork arms or other arms that can be raised 900 mm or more above the ground, but does not include a pedestrian-operated truck or a pallet truck.

    A person performing this work is required to hold a forklift truck high risk work (HRW) licence.
    This unit requires a person operating a forklift truck to plan the work, conduct routine checks on a forklift truck, shift loads in a safe manner, and safely shut down and secure equipment after completing operations.

    Licensing/Regulatory Information

    This unit is based on the licensing requirements of Part 4.5 of the Model Work Health and Safety (WHS) Regulations, HRW and meets Commonwealth, state and territory HRW licensing requirements.

    Any alteration to this unit would result in a unit that would not be acceptable to work health and safety (WHS)/occupational health and safety (OHS) regulators for the purpose of licensing.

    Pre-Requisites:
    Not applicable.

  • Course Code and Name:
    TLILIC3008 – License to operate a slewing mobile crane (up to 20 tonnes)

    This unit specifies the skills and knowledge required to safely operate a slewing mobile crane with a capacity up to 20 tonnes.

    Slewing mobile crane means a mobile crane incorporating a boom or jib that can be slewed, but does not include:

    • a front-end loader or
    • a backhoe or
    • an excavator or
    • other earth moving equipment, when configured for crane operation.

    This unit applies to the activities of a person operating slewing mobile crane with a capacity up to 20 tonnes that is a:

    • non-slewing mobile crane with a capacity exceeding 3 tonnes
    • reach stacker
    • slewing mobile crane with a capacity of 20 tonnes or less
    • vehicle loading crane with a capacity of 10 metre tonnes or more, excluding the application of load estimation and slinging techniques to move a load.

    A person performing this work is required to hold a slewing mobile crane – with a capacity up to 20 tonnes high risk work (HRW) licence.
    This unit requires a person operating slewing mobile crane with a capacity up to 20 tonnes to plan the work, conduct routine checks, set up crane, transfer a load, mobile load and shut down and secure the crane after completing the operation.

    Licensing/Regulatory Information

    This unit is based on the licensing requirements of Part 4.5 of the Model Work Health and Safety (WHS) Regulations, HRW and meets Commonwealth, state and territory HRW licensing requirements.

    Any alteration to this unit would result in a unit that would not be acceptable to work health and safety (WHS)/occupational health and safety (OHS) regulators for the purpose of licensing.

    Pre-Requisites:
    Not applicable.

  • Course Code and Name:
    TLILIC4009 Licence to operate a slewing mobile crane (up to 60 tonnes)

    This unit specifies the skills and knowledge required to safely operate a slewing mobile crane with a capacity up to 60 tonnes.

    Slewing mobile crane means a mobile crane incorporating a boom or jib that can be slewed, but does not include:

    • a backhoe or
    • an excavator or
    • a front-end loader or
    • other earth moving equipment, when configured for crane operation.

    This unit applies to the activities of a person operating a slewing mobile crane with a capacity up to 60 tonnes that is a:

    • non-slewing mobile crane with a capacity exceeding 3 tonnes
    • reach stacker
    • slewing mobile crane with a capacity of 60 tonnes or less
    • vehicle loading crane with a capacity of 10 metre tonnes or more, excluding the application of load estimation and slinging techniques to move a load.

    A person performing this work is required to hold a slewing mobile crane – with a capacity up to 60 tonnes high risk work (HRW) licence.

    This unit requires a person operating slewing mobile crane with a capacity up to 60 tonnes to plan the work, conduct routine checks, set up crane, transfer a load, mobile load and shut down and secure the crane after completing the operation.

    Licensing/Regulatory Information

    This unit is based on the licensing requirements of Part 4.5 of the Model Work Health and Safety (WHS) Regulations, HRW and meets Commonwealth, state and territory HRW licensing requirements.

    Any alteration to this unit would result in a unit that would not be acceptable to work health and safety (WHS)/occupational health and safety (OHS) regulators for the purpose of licensing.

    Pre-Requisites:
    Not applicable to this course.